Gadgets! Gadgets! Gadgets! All About How Gadgets Can Make Life Better and More Enjoyable

Down Voltage

Down Voltage

Voltage Characteristics and Solar Panels - Why So Many and What Do They Mean?

What's the big deal about Voltage?

In describing and designing renewable energy (RE) systems—especially photovoltaic (PV) systems—we routinely use what may first seem like a bewildering array of different voltage references. Not to worry, there's a logical explanation for all these numbers! Each is used for a particular purpose and each offers very useful information about an existing system or can help you to design an effective system.

Nominal Voltage

Nominal voltage is an approximation from the days when batteries were the typical unit of voltage measure (e.g., 2V, 6V, 12V). Thanks to the traditional use of solar modules as battery chargers, it happened that modules were usually designed to charge common battery voltages. Nominal ("by name" or "in name only"), in common RE use, has come to refer to those standard battery voltages and to systems and system components designed to be compatible with such voltages.

The tricky part is that the voltage values referred to aren't necessarily the values you will see in actual practice! For example, under full sunlight, a 12V nominal solar panel will typically produce about 17V DC (DC = direct current) ; if it's charging a 12V battery, that battery, when full, may register as high as 14.4V on a voltmeter. These small differences are normal and expected within the nominal range, and the "shorthand" of nominal voltage (12V in this case) is still a useful tool for us to discuss systems and related components.

System Voltage

Very similar to nominal voltage is system voltage . This word refers to the nominal voltage of the RE system as a whole. Since batteries are in many ways the heart of a battery-based RE system, we call the battery bank's voltage the system voltage. Almost all off-grid RE systems will use one of these three voltages: 12V, 24V, 48V. The system voltage of any given installation is usually, though not always, determined by the battery bank required by the application being served; the inverter, if one is used, will influence this decision as well.

These next two voltages refer to rated specifications of PV modules and are used in the design of systems and the comparison of modules.

Maximum Power Voltage

(commonly abbreviated Vmp or Vpmax)

Maximum power voltage refers to the "sweet spot"  where the solar panel produces the maximum power (power is equal to voltage times current) under full sunlight conditions.  For a 12V nominal crystalline silicon module, the peak power voltage will usually be between 16 and 18V DC, depending on the model of the solar module.

The voltage value you actually see on a voltmeter will depend on where you take the measurement within the system, whether the system is powering a load, what that load is (including the state of charge of the battery bank, if present), and other factors. Vmp is used to help determine the peak power (and from that, the total energy) the system can deliver.

Open Circuit Voltage (Voc)

If you measure a PV module under full sunlight when it is not connected to a system—that is, by touching a voltmeter's probes directly to the module's positive and negative terminals or cable ends, you'll be measuring the module's open circuit voltage . Setting aside environmental effects on voltage for a moment, open circuit voltage is theoretically the highest voltage a module will produce. In practice, certain conditions can cause a module's voltage to exceed Voc—and thereby increase the power output—but it's nevertheless an essential figure to system designers, used to match PV modules or arrays with other system components.

Each PV module is labeled with electrical specifications

Summary

As is often true with electricity and electrical components, voltage can be a slippery value to pin down. We use several voltage standards and component ratings to help us compare modules and design RE systems. Using these ratings in certain formulas helps ensure safe and efficient system design.

Nominal Voltage

Standard used to classify and compare system components; based on common battery voltages*

System Voltage

Nominal voltage of entire system; based on battery bank; usually 12V, 24V, 48V

Maximum Power Voltage (Vmp)

Voltage where a PV module produces its maximum power output while connected to a load.

Open Circuit Voltage (Voc)

Rated maximum voltage of a PV module when not connected to a load

*Nominal voltages for solar panels that can't be found in batteries, such as 18V, are increasingly common. These voltages are based on PV modules that were not designed specifically for battery-charging systems, such as those used in straight grid-tied PV systems. These voltage solar panels can be used with lower voltage battery banks, but require a Maximum Power Point Tracking (MPPT) type of solar charge controller to efficient down convert the DC voltage.

About the Author

Written by altE Store's Ben Gorman.

Founded in 1999, altE, Inc has catered to DIY customers on every continent of the globe. A 2006 Inc. 500 awarded company, altE aims to continue to fulfill its motto, "Making Renewable Do-able," by offering cost competitive, high-quality renewable energy related products and educational services to a broad spectrum of the public. For more information visit their website at www.altEstore.com or contact Toll Free (877) 878-4060.

Step-down voltage transformer Q: power here is 230v, but settings only include 220v or 240v. Which to use?

I just moved to Switzerland from the US and power here is 230v. I brought a couple of step-down transformers and they have specific settings on the back. Choices are 220v or 240v. Wondering which setting I should use as I want my electronic and other equipment to stay safe.

Appreciate the help!

Just my own personal opinion,

If the mains voltage coming from the wall socket is 230v and the choice of settings on the transformers are 220v or 240v then I would always use the 240v setting which will give me a slightly lower voltage to the equipment but not that much to matter.

If the transformer is set to 240v to supply an output of 12v for instance - then if you put in 230v you will get 1/20th of that voltage out which is about 11.5v
If the transformer is set on 220v for an output of 12v for instance - if you put in 230v you will get a slightly higher voltage out (about 12.5v)

A transformer works on a voltage ratio principle (ignoring losses)
for example 240v (setting) divided by 12v = 20 therefore 230v divided by 20 = 11.5v (slightly lower voltage going to the equipment)
but 220v (setting) divided by 12v = 18.333 therefore 230v divided by 18.333 = 12.5v (slightly higher voltage going to the equipment)

Down - Lysergik Funeral Procession @ High Voltage Festival 25th July 2010